雙組份打膠機控制體系采用PLC和觸摸屏，人機界面，一鍵操作。該設備操作簡略，運用方便。伺服控制體系選用世界名牌(日本安川)，功能更穩定。滿意設備運轉要求，玻璃污染可忽略不計。只需一人操作設備即可完結整塊玻璃的上膠。穩定可靠，出產效率高。雙組份打膠機由A、B膠泵、氣動體系、升降結構、機架等組成。那么在運用雙組份打膠機時留意什么問題呢?讓我們來了解一下。
PLC and touch screen are used in the control system of the two-component gluing machine, with man-machine interface and one key operation. The equipment is simple to operate and easy to use. The servo control system adopts the world famous brand (Yaskawa, Japan), with more stable functions. The glass pollution can be ignored. Only one person can operate the equipment to finish the gluing of the whole glass. Stable and reliable, high production efficiency. The two-component gluing machine is composed of a and B glue pumps, pneumatic system, lifting structure, frame, etc. So what problems should we pay attention to when using the two-component gluing machine? Let's have a look.
1. 因為雙組份打膠機的固化需求必定的時刻，所以涂有雙組份密封劑的玻璃需求水平移動。
1. Because the curing requirement of the two-component sealant is certain, the glass coated with the two-component sealant needs to move horizontally.
2. A組和B組的膠要保持清潔，嚴禁異物進入膠內。
2. The glue of group A and group B should be kept clean, and no foreign matter is allowed to enter the glue.
3.連續運轉過程中，膠槍中止時刻不超越20分鐘。否則，應運用膠水的組成部分沖刷一切混合的膠水，直到一個單一的組成部分的膠水從槍口排出。
3. During continuous operation, the stop time of glue gun shall not exceed 20 minutes. Otherwise, the glue components should be used to flush all mixed glue until a single component of glue is discharged from the muzzle.

4. 不得強行擠壓或曲折高壓軟管，以免影響體系的正常運轉。
4. Do not squeeze or bend the high-pressure hose by force to avoid affecting the normal operation of the system.
5. 混合器應始終保持疏通，以確保杰出的粘合劑作用。若阻塞，浸泡后用丙酮沖刷。主張每5套洗一次。
5. The mixer should be kept clear at all times to ensure excellent adhesive effect. If blocked, wash with acetone after soaking. Wash every 5 sets.
6. 當膠槍長時刻不運用(超越一周)時，應將膠槍本體取出，用溶劑清洗膠槍和混合器內殘留的凝膠。
6. when the rubber gun is not used for longer than a week, the rubber gun body should be removed and the residual gel in the rubber gun and mixer should be cleaned with solvents.
7. 不同雙組份打膠機出產的膠中雜質的含量不同。根據實際情況，B組件的濾網和單向止回閥每兩組清洗一次。
7. The content of impurities in the glue produced by different two-component gluing machines is different. According to the actual situation, the filter screen and one-way check valve of assembly B are cleaned once every two groups.
8. 因為膠槍、管道或機器的膠態固化而形成的明顯缺陷都不在保修范圍內。
8. Any defects caused by glue curing of glue gun, pipe or machine are not covered by warranty.
9. 定時向雙組份打膠機各泵的加油口加注油，確保油在霧化器內繼續存在。
9. Add oil to the oil filler of each pump of the two-component glue applicator regularly to ensure that the oil continues to exist in the atomizer.
以上就是對雙組份打膠機留意事項的詳細介紹，想要了解更多請關注公司網站：http://linshi.jncsjx.com后續會呈現更多精彩內容。
The above is a detailed introduction to the matters needing attention of the two-component gluing machine http://www.hebeiruizhi.com More exciting content will be presented later.