當前位置：涂布機噴膠設備保養要注意什么？
時間：2023-02-25 來源：http://www.hebeiruizhi.com/ 發布人：昌盛機械
1、在進行拆卸保養維修工作時，工作者好不要穿戴耳環、手表、項鏈、手鐲等可以導電的裝飾品，防止事故發生。
1. When carrying out disassembly, maintenance and repair work, workers should not wear earrings, watches, necklaces, bracelets and other conductive ornaments to prevent accidents.
2. 在進行保養維修熱熔膠涂布機的工作之前，必須先把熱熔膠涂布機械上的電源用戶及聯拉外界的總電源給切斷，不得帶電操作。
2. Before maintenance and repair of the hot melt adhesive coating machine, the power user of the hot melt adhesive coating machine and the main power supply of the external coupling must be cut off first, and live operation is not allowed.
3、不要隨便拆卸檢查調整熱熔膠涂布機上之任何零件，除非你對設備性能有足夠了解。
3. Do not disassemble, check and adjust any parts on the hot melt adhesive coating machine, unless you have sufficient knowledge of the equipment performance.
4、除非有其他人員在旁邊協助，并且在發生意外，因機械的損壞或人員的受傷時，可以即刻給于幫助或急救，否則不要單獨對熱熔膠涂布機設備進行拆裝與維修。
4. Do not disassemble and repair the hot melt adhesive coater equipment separately unless there are other personnel nearby for assistance and immediate help or first aid can be given in case of accident, mechanical damage or personal injury.
5、只有合格的人員才可以對熱熔膠涂布機進行維修保養的工作。
5. Only qualified personnel can repair and maintain the hot melt adhesive coating machine.
6、在任何情況下,不要隨意觸碰可能暴露于外界的電線接頭或其他有電線聯接且未松脫之元件。
6. Under any circumstances, do not touch the wire connectors or other components connected by wires that may be exposed to the outside without looseness.
7、拆卸或移動熱熔膠涂布機上之保護裝置或更換元器元件之前，必須先切斷電源的供應。
7. Before removing or moving the protective device on the hot melt adhesive coating machine or replacing the element, the power supply must be cut off first.
8、如果可能的話，盡量站在塑膠毯上進行保養維修的工作。千萬不要在有淹水的地板或非常潮濕的環境下對熱熔膠涂布機進行維護工作。
8. If possible, try to stand on the plastic blanket for maintenance. Do not carry out maintenance work on the hot-melt adhesive coating machine in a flooded floor or in a very humid environment.
9、對熱熔膠涂布機進行維護與維修時必須穿戴安全手套、護目鏡及長袖工作服，避免身體部份被高溫的液態熱溶膠燙傷，或被高溫的元件表面灼傷。
9. Safety gloves, goggles and long-sleeved work clothes must be worn during the maintenance and repair of the hot melt adhesive coating machine to prevent the body part from being scalded by the hot liquid hot melt adhesive or the surface of the hot element.
10、松脫或安裝壓力接頭時，必須確定為熱熔膠涂布機提供壓力氣源的壓力已減低至零值。
10. When loosening or installing the pressure joint, it must be ensured that the pressure of the pressure air supply for the hot melt adhesive coater has been reduced to zero.
11、清洗熱熔膠熔膠缸時，避免使用有焰火或尖銳的硬質工具，以免刮傷膠桶內部的鐵氟龍不粘膠涂層。
11. When cleaning the hot melt glue cylinder, avoid using hard tools with fireworks or sharp edges to avoid scratching the Teflon non-stick coating inside the rubber barrel.
上一篇：雙道密封鋁隔條式中空玻璃制作標準
下一篇：中空玻璃設備基本保養常識你都清楚嗎？
相關新聞 more+
- 中空玻璃打膠機，助您開啟高效生產新時代！ 2026/02/19
- 中空玻璃生產線打膠機傳送V帶不平衡？這樣調，傳送平穩不跑偏 2026/02/13
- 中空玻璃生產線打膠難題：壓力夠卻打不滿膠？這樣排查就解決 2026/02/12
- 全自動封膠線實操科普：山東昌盛板壓段，筑牢封膠質量核心防線 2026/02/10
- 中空玻璃生產線實操科普：小玻璃清洗機反轉打滾？這樣解決最省心 2026/02/06
- 全自動封膠線實操科普：白膠泵密封圈這樣換，杜絕漏膠保順暢 2026/02/04
- 雙組份打膠機實操科普：出膠體這樣保養維護，延長壽命保順暢 2026/02/02
- 中空玻璃生產線：清洗機這樣保養，清潔高效更耐用 2026/01/30
- 全自動封膠線實操科普：板壓壓合效果差？四角落差這樣調精準 2026/01/28
- 雙組份打膠機實操科普：黑膠泵過濾這樣清洗，避免堵塞保順暢 2026/01/27
產品分類Product categories
聯系我們Contact us
