雙組份涂膠機由A、B膠泵、氣動系統、提升機構、機架組成。以下是:
　　The two-component glue applicator consists of a and B glue pumps, pneumatic system, lifting mechanism and frame. The following are:
　　1. 膠泵:
　　1. glue pump:
　　(1) A、B部件分別裝有橡膠泵，橡膠泵由A、B兩部件各自的氣動馬達驅動，往復運動，分別吸進、壓出橡膠。A、B膠泵分別與壓膠盤固定在一起，再與機架連接形成各自的系統。
　　(1) Parts A and B are respectively equipped with rubber pumps, which are driven by the respective pneumatic motors of parts A and B, which move back and forth to respectively suction and discharge rubber. A. B glue pump is respectively fixed with the pressure glue disk, and then connected with the frame to form their own system.
　　(2) A、B組份比例通過比例杠桿調節:B組份比例向內調節膠量減少，向外調節膠量增加。通過調節比例桿來控制B膠的出膠量，從而控制A膠和B膠的比例。
　　(2) The proportion of component A and component B is adjusted by the proportion lever: the amount of glue of component B is decreased inwards and increased outwards. By adjusting the proportion bar, the glue output of B glue is controlled, so as to control the proportion of a glue and B glue.

　　(3)出膠量:由氣源處理器控制，逆時針調節出膠量增加，順時針調節出膠量減少。(這里是指總膠量)
　　(3) Glue output: controlled by the air source processor, adjust the glue output anticlockwise to increase, and adjust the glue output clockwise to decrease. (here refers to the total glue quantity)
　　該膠泵通過比例杠桿調節A、B膠的體積比，具有操作靈活、性能穩定、調節范圍大等特點。
　　The rubber pump can adjust the volume ratio of a and B rubber through the proportional lever, which has the characteristics of flexible operation, stable performance and large adjustment range.
　　2. 提升機制:
　　2. Promotion mechanism:
　　組件A和組件B膠泵分別設有一套氣動升降機構，該氣動升降機構由兩個氣缸并聯組成，通過橫梁與各自的泵體固定。其目的之一是通過壓力板將兩個圓柱體的力作用在膠粘表面上。第二，當需要更換橡皮桶時，氣缸可以抬起壓力板。把鼓留下，換一個新的。
　　The rubber pump of component A and component B are respectively provided with a set of pneumatic lifting mechanism, which is composed of two cylinders in parallel, and is fixed with the respective pump body through the crossbeam. One of its purposes is to apply the force of two cylinders on the adhesive surface through a pressure plate. Second, when the rubber bucket needs to be replaced, the cylinder can lift the pressure plate. Leave the drum and replace it with a new one.
　　以上就是對雙組份打膠機的結構運作原理的詳細介紹，想要了解更多請點擊官網http://www.hebeiruizhi.com
　　The above is a detailed introduction to the structure and operation principle of the two-component dispenser. For more information, please click http://www.hebeiruizhi.com